Macs Stang
11-16-2004, 12:06 PM
Hey my name is Tim and I am from Minnesota.
I have a '91 Mustang GT that I have owned for the last three years.
The car was completely bone stock, save for a crappy HD clutch.
I have done all the work on my car, except for the tranny, cam, and rear end gears which were done by Dan @ DB Performance.
Here are the mods I have on my car.
Engine:
302 cu in (167,xxx miles on the short block :naughty: )
TFS street intake
e-303 cam
Ported/Polished 1.84/1.46 E7 heads
1.6 roller rockers
Under Drive Pullies
70mm tb
76mm maf
Fenderwall CAI
Electric Fan
FPR
1 5/8 Long Tubes
2 1/2 o/r hpipe
2 1/2 original flowmaster 40's dumped
Drivetrain:
Tremec 3550
Spec stage 2 clutch
Pro 5.0 short throw
Steeda quad/adjuster
Poly motor/trans mounts
3.73's
McLeod Steel Bellhousing
Suspension:
BBK progressive rate springs (front)
stock V8 springs (rear)
KYB adjustable struts
Hotchkis Lower control arms
Wheels:
Weld Drag Lites (Track)
Stock Pony's (Street)
Tires:
205/60/15's Futuras (front, track)
26x11.50-15 M/T ET Streets (Track)
225/50/16 Dunlops (Front)
245/50/16 Nitto 450's (Rear)
Gauges:
5 inch Phantom monster tach
2 1/16 water temp, oil pressure, volt all in phantom.
The best the car has ran was a 13.258@102.73 with a 1.805 60 ft.
The last time I went to the track was the first time I was able to use the ET Streets, so there is a lot of learning to do with these tires.
http://www.mustangmods.com/data/10546/pic.jpg
http://www.mustangmods.com/data/10546/side.jpg
http://www.mustangmods.com/data/10546/welds_rear2.jpg
http://www.mustangmods.com/data/10546/don_tim_3.jpg
http://www.mustangmods.com/data/10546/tim_burnout.jpg
I have a '91 Mustang GT that I have owned for the last three years.
The car was completely bone stock, save for a crappy HD clutch.
I have done all the work on my car, except for the tranny, cam, and rear end gears which were done by Dan @ DB Performance.
Here are the mods I have on my car.
Engine:
302 cu in (167,xxx miles on the short block :naughty: )
TFS street intake
e-303 cam
Ported/Polished 1.84/1.46 E7 heads
1.6 roller rockers
Under Drive Pullies
70mm tb
76mm maf
Fenderwall CAI
Electric Fan
FPR
1 5/8 Long Tubes
2 1/2 o/r hpipe
2 1/2 original flowmaster 40's dumped
Drivetrain:
Tremec 3550
Spec stage 2 clutch
Pro 5.0 short throw
Steeda quad/adjuster
Poly motor/trans mounts
3.73's
McLeod Steel Bellhousing
Suspension:
BBK progressive rate springs (front)
stock V8 springs (rear)
KYB adjustable struts
Hotchkis Lower control arms
Wheels:
Weld Drag Lites (Track)
Stock Pony's (Street)
Tires:
205/60/15's Futuras (front, track)
26x11.50-15 M/T ET Streets (Track)
225/50/16 Dunlops (Front)
245/50/16 Nitto 450's (Rear)
Gauges:
5 inch Phantom monster tach
2 1/16 water temp, oil pressure, volt all in phantom.
The best the car has ran was a 13.258@102.73 with a 1.805 60 ft.
The last time I went to the track was the first time I was able to use the ET Streets, so there is a lot of learning to do with these tires.
http://www.mustangmods.com/data/10546/pic.jpg
http://www.mustangmods.com/data/10546/side.jpg
http://www.mustangmods.com/data/10546/welds_rear2.jpg
http://www.mustangmods.com/data/10546/don_tim_3.jpg
http://www.mustangmods.com/data/10546/tim_burnout.jpg